rev.6.00 jun 15, 2005 page 1 of 9 HA17L431/HA17L431a series shunt regulator rej03d0691-0600 (previous: ade-204-029e) rev.6.00 jun 15, 2005 description the HA17L431 series and the HA17L431a series are temperature-compensated variable shunt regulators. these ics can operate at about half voltage in comparison with ha17431 series. they can be replaced for simple zener diode and they can also be used for switching power supply secondary-side error amplification circuit. features ? on-chip high-precision reference voltage source : 1.240 v 1.0% at ta = 25 c (HA17L431a) : 1.240 v 1.5% at ta = 25 c (HA17L431) ? small reference voltage temperature coefficient: 30 ppm/ c typ ? maximum cathode voltage: 16 v ? maximum cathode current: 50 ma ? minimum cathode current: 200 a typ ? operating temperature range: ? 20 to +85 c block diagram a + ? ref k 1.240 v application circuit example vout + ? a k ref r2 r1 HA17L431/HA17L431a gnd r switching power supply secondary-side error amplification circuit
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 2 of 9 product lineup reference voltage (at 25c) item normal version 1.5% 1.222v to 1.258v to 1.240v a version 1.0% 1.227v to 1.253v to 1.240v package code (previous code) operating temperature range HA17L431lp o plsp0005zb-a (mpak-5v) HA17L431alp o HA17L431p o prss0003da-a (to-92v) HA17L431ap o HA17L431up o plzz0004ca-a (upakv) ha17l432up o HA17L431altp o plsp0003zb-a (mpakv) industrial use ha17l432altp o ?20 to +85c pin arrangement upakv (HA17L431up) a a k ref upakv (ha17l432up) a a ref k mpak-5v (HA17L431lp/alp) nc k nc ref a mpakv (HA17L431altp) k ref a 123 1 3 21 123 123 3 2 5 4 ref k a mpakv (ha17l432altp) a k ref 2 3 1 mark side to-92v (HA17L431p/ap)
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 3 of 9 absolute maximum ratings (ta = 25 c) rated value item symbol HA17L431lp/ HA17L431alp HA17L431p/ HA17L431ap HA17L431up/ ha17l432up HA17L431altp/ ha17l432altp unit note cathode voltage v ka 16 16 16 16 v 1 continuous cathode current i k ? 30 to +50 ? 30 to +50 ? 30 to +50 ? 30 to +50 ma reference input current iref ? 0.05 to +5 ? 0.05 to +5 ? 0.05 to +5 ? 0.05 to +5 ma power dissipation p t 150 500 800 150 mw 2 operating temperature topr ? 20 to +85 ? 20 to +85 ? 20 to +85 ? 20 to +85 c storage temperature tstg ? 55 to +150 ? 55 to +150 ? 55 to +150 ? 55 to +150 c notes: 1. the anode pin is used as the reference for voltage values. 2. these values apply when ta 25 c. if ta 25 c, derate by below figure. ? 20 0 50 75 85 25 150 0.6 0.5 0.5w 0.4 power dissipation p t (w) ambient temperature ta ( c) (1) (2) 0.3 0.26 0.2 0.1 0.15w ? 1.2mw/ c 0.078 ? 4mw/ c ? 20 0 50 75 85 25 150 1.2 1.0 0.8w 0.8 power dissipation p t (w) ambient temperature ta ( c) (1): HA17L431p/ap (2): HA17L431lp/alp/altp/432altp HA17L431up/432up (1): with 15mm 25mm 0.7mm alumina ceramic board (2): without printed circuit board (1) (2) 0.6 0.416 0.4 0.2 0.385w ? 3.08mw/ c ? 6.4mw/ c
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 4 of 9 electrical characteristics (ta = 25 c, i k = 10 ma) item symbol min typ max unit test condition remark 1.222 1.240 1.258 HA17L431 reference voltage vref 1.227 1.240 1.253 v v ka = vref HA17L431a reference voltage deviation vref(dev) ? 5 ? mv v ka = vref, ta = ? 20c to +85 c * 1 reference voltage temperature coefficient ? vref/ ? ta ? 30 ? ppm/ c v ka = vref, 0c to 50 c gradient reference voltage regulation ? vref/ ? v ka ? 1.0 2.0 mv/v v ka = vref to 16v reference input current iref ? 2 6 a r1 = 10 k ? , r2 = reference current temperature deviation iref(dev) ? 0.5 ? a r1 = 10 k ? , r2 = , ta = ? 20 c to +85 c minimum cathode current imin ? 0.2 1.0 ma v ka = vref * 2 off cathode current ioff ? 0.001 1.0 a v ka = 16 v, vref = 0 v dynamic impedance z ka ? 0.2 0.5 ? v ka = vref, i k = 1 ma to 50 ma notes: 1. vref(dev) = (vref maximum value at ta = ? 20 c to +85 c) ? (vref minimum value at ta = ? 20 c to +85 c) vref(dev) ? 20 +85 ta ( c) 2. definition of minimum cathode current. imin is the cathode current value at which vref = vref (i k = 10 ma) ? 15 mv.
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 5 of 9 mpak-5v(5-pin), mpakv(3-pin) and upakv marking patterns the marking patterns shown below are used on mpak-5v, mpakv and upakv products. note that the product code and mark pattern are different. the pattern is laser-printed. HA17L431lp HA17L431altp HA17L431up ha17l432up ha17l432altp (b) (2) (c) (4) (1) (a) l 4 a ref nc nc k HA17L431alp (b) (2) (c) (4) (1) (a) m 4 a ref nc nc k (b) (2) (c) (4) (1) (a) e 3 a ref k (b) (2) (c) (4) (1) (a) f 3 a k ref (3) (4) (1) (2) (5) ref aa k 4d k a ref (3) (4) (1) (2) (5) 4e band mark band mark notes: 1. boxes (1) to (5) in the figures show the position of the letters or numerals, and are not actually marked on the package. 2. the letters (1) and (2) show the product specific mark pattern. product (1) (2) HA17L431lp 4 l HA17L431alp 4 m HA17L431altp 3 e ha17l432altp 3 f HA17L431up 4 d ha17l432up 4 e 3. the letter (3) shows the production year code (the last digit of the year) for upakv products. 4. the bars (a), (b) and (c) show a production year code for mpak-5v and mpakv products as shown below. after 2010 the code is repeated every 8 years. year 2002 2003 2004 2005 2006 2007 2008 2009 (a) none none none bar bar bar bar none (b) none bar bar none none bar bar none (c) bar none bar none bar none bar none 5. the letter (4) shows the production month code (see table below). production month jan. feb. mar. apr. may. jun. jul. aug. sep. oct. nov. dec. marked code a b c d e f g h j k l m 6. the letter (5) shows manufacturing code. for upakv products.
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 6 of 9 characteristic curves 1.260 1.250 1.230 1.220 ? 20 0 20 40 60 80 85 1.0 0.5 0 0 0.5 1 1.5 2.0 2.5 1.240 500mv/div ref k a vref 50 0 ? 30 ? 50 5 1v/div 50 0 100 1k 100k 1m 10m 0 180 ? 180 10k ? vo vi 4.3k ? 10 f g = 20log vo vi (db) g vol v k = vref i k = 10ma i k v ref k a i k = 10ma v k = vref v k = vref 220 ? 6.8k ? ? + ambient temperature ta ( c) reference voltage vref (v) temperature characteristics of reference voltage catode voltage v k (v) catode current i k (ma) catode current vs. catode voltage1 catode voltage v k (v) catode current i k (ma) catode current vs. catode voltage2 frequency f (hz) open loop voltage gain g vol (db) open loop voltage gain, phase vs. frequency characteristics phase ? (degree)
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 7 of 9 noise recovery characteristics of HA17L431a and HA17L431 the HA17L431a bettered v ka and vref recovery time against the HA17L431 when it was inputted noise. 15 v 220 pf (external) 12 k ? input pulse 1 v 680 ? 7.5 k ? 220 f 4.7 k ? 0.1 f 0 v 50 ms (cathode) (anode) shunt regulators (ref) pulse generator v ka vref vout figure 1 noise response characteristics measurement circuit 1 2 trig? tek run: 25.0ms/s sample ch1 ch3 500mv 1.00 v ch2 ch2 2.46 v 1.00 v m 2.00 s t [ ????? t ????????????????????????????????????????????????????????? ] 1 2 trig? tek run: 25.0ms/s sample ch1 ch3 500mv 1.00 v ch2 ch2 2.46 v 1.00 v m 2.00 s t [ ????? t ????????????????????????????????????????????????????????? ] waveform of HA17L431a waveform of HA17L431 input noise v ka vref input noise v ka vref figure 2 noise recovery characteristics
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 8 of 9 package dimensions d e a qc aa b xsa a a 2 a 1 m e l h e l 1 l p a 3 ys pattern of terminal position areas s i 1 b 2 e e 1 a a 1 a 2 a 3 b b 1 c c 1 d e e h e l l 1 l p x y b 2 e 1 i 1 q 1.0 0 1.0 0.35 0.1 2.8 1.5 2.5 0.3 0.1 0.2 min nom dimension in millimeters reference symbol max 1.1 0.25 0.42 0.4 0.13 0.11 2.95 1.6 0.95 2.8 2.15 0.3 1.3 0.1 1.2 0.5 0.15 3.1 1.8 3.0 0.7 0.5 0.6 0.05 0.05 0.55 0.85 sc-74a 0.015g mass[typ.] mpak-5 / mpak-5v plsp0005zb-a renesas code jeita package code previous code b a-a section b 1 c 1 c d e a aa b xsa m e h e a a 2 a 1 s b a-a section b 1 c 1 c qc l l 1 l p a 3 pattern of terminal position areas i 1 b 2 e e 1 a a 1 a 2 a 3 b b 1 c c 1 d e e h e l l 1 l p x b 2 e 1 i 1 q 1.0 0 1.0 0.35 0.1 2.7 1.35 2.2 0.35 0.15 0.25 min nom dimension in millimeters reference symbol max 1.1 0.25 0.42 0.4 0.13 0.11 1.5 0.95 2.8 1.95 0.3 1.3 0.1 1.2 0.5 0.15 3.1 1.65 3.0 0.75 0.55 0.65 0.05 0.55 1.05 sc-59a 0.011g mass[typ.] mpak(t) / mpak(t)v, mpak / mpakv plsp0003zb-a renesas code jeita package code previous code
HA17L431/HA17L431a series rev.6.00 jun 15, 2005 page 9 of 9 4.5 0.1 1.8 max 1.5 0.1 0.44 max 0.44 max 0.48 max 0.53 max 1.5 1.5 3.0 2.5 0.1 4.25 max 0.8 min 1 0.4 (1.5) (2.5) (0.4) (0.2) previous code plzz0004ca-a upak / upakv mass[typ.] 0.050g sc-62 renesas code jeita package code unit: mm 0.60 max 0.55 max 4.8 0.3 3.8 0.3 5.0 0.2 0.7 2.3 max 12.7 min 0.5 max 1.27 2.54 previous code prss0003da-a to-92(1) / to-92(1)v mass[typ.] 0.25g sc-43a renesas code jeita package code unit: mm
keep safety first in your circuit designs! 1. renesas technology corp. puts the maximum effort into making semiconductor products better and more reliable, but there is al ways the possibility that trouble may occur with them. trouble with semiconductors may lead to personal injury, fire or property damage. remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. notes regarding these materials 1. these materials are intended as a reference to assist our customers in the selection of the renesas technology corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to renesas t echnology corp. or a third party. 2. renesas technology corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating i n the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. all information contained in these materials, including product data, diagrams, charts, programs and algorithms represents in formation on products at the time of publication of these materials, and are subject to change by renesas technology corp. without notice due to product improvement s or other reasons. it is therefore recommended that customers contact renesas technology corp. or an authorized renesas technology corp. product distrib utor for the latest product information before purchasing a product listed herein. the information described here may contain technical inaccuracies or typographical errors. renesas technology corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or e rrors. please also pay attention to information published by renesas technology corp. by various means, including the renesas technolo gy corp. semiconductor home page (http://www.renesas.com). 4. when using any or all of the information contained in these materials, including product data, diagrams, charts, programs, an d algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. renesas technology corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. renesas technology corp. semiconductors are not designed or manufactured for use in a device or system that is used under cir cumstances in which human life is potentially at stake. please contact renesas technology corp. or an authorized renesas technology corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerosp ace, nuclear, or undersea repeater use. 6. the prior written approval of renesas technology corp. is necessary to reprint or reproduce in whole or in part these materia ls. 7. if these products or technologies are subject to the japanese export control restrictions, they must be exported under a lice nse from the japanese government and cannot be imported into a country other than the approved destination. any diversion or reexport contrary to the export control laws and regulations of japan and/or the country of destination is pro hibited. 8. please contact renesas technology corp. for further details on these materials or the products contained therein. sales strategic planning div. nippon bldg., 2-6-2, ohte-machi, chiyoda-ku, tokyo 100-0004, japan http://www.renesas.com refer to " http://www.renesas.com/en/network " for the latest and detailed information. renesas technology america, inc. 450 holger way, san jose, ca 95134-1368, u.s.a tel: <1> (408) 382-7500, fax: <1> (408) 382-7501 renesas technology europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k. tel: <44> (1628) 585-100, fax: <44> (1628) 585-900 renesas technology hong kong ltd. 7th floor, north tower, world finance centre, harbour city, 1 canton road, tsimshatsui, kowloon, hong kong tel: <852> 2265-6688, fax: <852> 2730-6071 renesas technology taiwan co., ltd. 10th floor, no.99, fushing north road, taipei, taiwan tel: <886> (2) 2715-2888, fax: <886> (2) 2713-2999 renesas technology (shanghai) co., ltd. unit2607 ruijing building, no.205 maoming road (s), shanghai 200020, china tel: <86> (21) 6472-1001, fax: <86> (21) 6415-2952 renesas technology singapore pte. ltd. 1 harbour front avenue, #06-10, keppel bay tower, singapore 098632 tel: <65> 6213-0200, fax: <65> 6278-8001 renesas sales offices ? 200 5. re nesas technology corp ., all rights reser v ed. printed in ja pan. colophon 2.0
|
